3
4
English
Our products are designed to meet the
highest standards of quality, functionality and
design. We hope you enjoy your new Braun
Shaver.
• The red low-charge light glows when the
shaver capacity has dropped below 20%
provided the shaver is switched on. The
remaining capacity will then be sufficient
for 2 to 3 shaves.
Warning
• If the rechargeable batteries are discharg-
ed, you may also shave by connecting the
shaver to an electrical outlet via the special
cord set.
Your shaver is provided with a special cord set
with integrated Safety Extra Low Voltage
power supply. Do not exchange or manipulate
any part of it. Otherwise there is risk of electric
shock.
Shaving
Press the on/off switch (4) to turn the shaver
on.
Description
1 Shaver foil
2 Cutter block
3 Release button
4 On/off switch («start/stop»)
5 Long hair trimmer
6 Charging light (green)
7 Low-charge light (red)
8 Special cord set
Trimmer:
When the long hair trimmer (5) is activated, it
allows the controlled trimming of moustache
or sideburns.
Tips for the perfect shave
• We recommend that you shave before
washing, as the skin tends to be slightly
swollen after washing.
• Hold the shaver at right angles (90°) to the
skin. Stretch the skin and shave against
the direction of beard growth.
• To maintain 100% shaving performance,
replace the shaver foil and cutter block at
least every 18 months or when worn.
Charging
The best environmental temperature for
charging is between 15 °C and 35 °C.
• Connect the shaver to an electrical outlet
with the motor switched off.
• When charging for the first time, leave the
shaver to charge continuously for 4 hours.
• The green charging light (6) shows that
the shaver is being charged. When the
batteries are fully charged, the charging
light intermittently blinks on and off. This
indicates that the battery maintains its full
capacity.
• Once the shaver is completely charged,
discharge the shaver through normal use.
Then recharge to full capacity. Subsequent
charges will take about 1 hour.
• A full charge provides up to 40 minutes of
cordless shaving time depending on your
beard growth. However, the maximum
battery capacity will only be reached after
several charging/discharging cycles.
Cleaning
This appliance is suitable for cleaning
under an open water tap.
Warning: Detach the hand-held part
from the power supply before cleaning it in
water.
Regular cleaning ensures better shaving
performance. Rinsing the shaving head after
each shave under running water is an easy
and fast way to keep it clean:
• Switch the shaver on (cordless) and rinse
the shaving head under hot running water.
5
A natural based soap may also be used
provided it contains no particles or
Environmental notice
abrasive substances. Rinse off all foam and
let the shaver run for a few more seconds.
• Next, switch off the shaver and press the
release buttons. Remove the shaver foil
and the cutter block. Then leave the
disassembled shaving parts to dry.
This product contains rechargeable
batteries. In the interest of protecting
the environment, please do not dispose
of the product in the household waste
at the end of its useful life. Disposal can
take place at a Braun Service Centre or at
appropriate collection points provided in
your country.
Alternatively, you may clean the shaver using
the brush provided:
• Switch off the shaver. Remove the shaver
foil.
Subject to change without notice.
• Using the brush, clean the cutter block and
the inner area of the shaver head. However,
do not clean the shaver foil with the brush
as this may damage the foil.
This product conforms to the European
Directives EMC 89/336/EEC and Low
Voltage 73/23/EEC.
Keeping your shaver in top shape
For electric specifications, see printing on the
special cord set.
About every four weeks, clean the cutter block
with Braun cleaning agents. Put a drop of light
machine oil onto the long hair trimmer and the
shaver foil.
Preserving the batteries
In order to maintain the optimum capacity
of the rechargeable batteries, the shaver
has to be fully discharged (by shaving) every
6 months approximately. Then recharge the
shaver to full capacity. Do not expose the
shaver to temperatures higher than 50 °C for
extended periods of time.
Replacing the shaving parts
To maintain 100% shaving performance
replace your foil and cutter block at least every
18 months or when worn. Change both parts
at the same time for a closer shave with less
skin irritation.
(Shaver foil and cutter block: 4000 series)
5-742-463/01/VI-07
Korea/GB
6
|